P1 Volvo Rear Camber Arms: Why Lowering Eats Your Tyres
Lower a C30, S40, V50 or C70 and the rear wheels tuck in, often eating the inner tyre edges. Here's why it happens, when camber arms help, and what to ask for at a four-wheel alignment.
You've lowered a C30, S40, V50 or C70, it sits properly at last, and a few thousand miles later the inside edges of the rear tyres are gone. The outer tread still looks fine. If that sounds familiar, you're not imagining it.
It's usually rear camber. Lowering a P1 tucks the top of the rear wheels in, and the standard camber arms can't be adjusted to put it back. Here's what's going on, when adjustable arms are worth fitting, and what I'd tell the alignment garage afterwards.
Quick Guide: When Do You Need Camber Arms?
| Situation | What I'd do |
|---|---|
| Stock height, even rear wear | Probably nothing yet. Get it measured if you're unsure. |
| Stock height, inner rear wear | Get a four-wheel alignment. If camber is too negative and they can't adjust it, fit camber arms. |
| Typical 30mm spring drop | Fit camber arms when you lower it, then get it aligned. |
| Lower still, on coilovers | Camber arms, and seriously consider toe arms as well, then a proper alignment. |
| Track or show stance | Adjustable camber arms, often toe arms too, set to the way you actually use the car. |
Why Lowering Adds Negative Rear Camber
The P1 has a multi-link rear axle. The wheel is located by several arms, including an upper camber arm, and those arms move in an arc as the suspension travels. A bit of negative camber — the top of the wheel leaning in — helps keep the tyre flatter on the road in a corner, and Volvo designed a fair amount of it into these cars from the factory. That geometry only works properly at the ride height it was designed for. Drop the car on springs or coilovers and the rear sits in a more compressed part of its travel, all the time, so the top of the wheel tucks in further. That's more negative camber, just from sitting lower.
The standard upper camber arm is a fixed length. An alignment shop can check rear camber, but they can't adjust it on the original arms. They can usually still adjust rear toe, within the range of the factory eccentric on the lower arm. Camber is the one that runs out of options.
This isn't only a lowered-car problem. Some standard-height P1s already sit quite negative at the rear, and Volvo even issued a service upper arm for cars that were too far out from the factory. That still isn't adjustable, though, so once you've lowered the car you want something you can actually set.
The Tell-Tale Sign: Inner-Edge Rear Tyre Wear
The symptom people search for is almost always the same: the inner shoulder of the rear tyres is worn smooth, sometimes down to the cords, while the outer edge still has plenty of tread. The tyre can end up looking slightly coned, and you might also see cupping or feathering on the inner blocks.
It's easy to blame camber for everything, though. Rear toe will also wear an edge if it's out, worn bushes can let the geometry wander under load, and under-inflation makes any of that worse. If you're not sure, get the car measured before you buy another set of tyres.
What Adjustable Rear Camber Arms Actually Do
Adjustable rear camber arms replace that fixed upper arm with one you can lengthen or shorten. Lengthen it and you bring the top of the wheel back out, towards zero. Shorten it and you add more negative camber, which is what you'd do for a track or show setup. Once they're on the car, the garage can actually set the figure you want.
Our own ÄLG Adjustable Camber Arms are the ones I'd start with on a P1. They're made from S355 steel, powder coated in our orange so they match the lowering springs, and they use large bearings and hardened rubber bushes. The product page lists up to -8 degrees of camber adjustment, which is more than enough to get a lowered road car back to sensible numbers, or to go more aggressive if that's what you're after.
They fit the C30, C70, S40 (including AWD) and V50 (including AWD). They also fit the later V40 (2012+) and the related Ford Focus ST/RS Mk2 and Mazda 3 BK.
If you want a forged alternative, we also stock the Hardrace Forged Camber Arms, with hardened rubber bushes as standard or a pillowball option for a stiffer, more track-focused setup. For a daily, I'd stay with the rubber-bushed arms, ours or the Hardrace ones. Fitting the arms doesn't set the camber on its own, though, so don't just copy the length of the old arms and call it done.
How Much Drop Before You Need Them?
There isn't a magic number in millimetres. It depends on the car, the chassis, how worn the original arms and bushes are, and how far you've gone. The table above is how I'd think about it.
A typical 30mm spring drop, like our ÄLG P1 Lowering Springs, is already enough that I'd fit camber arms at the same time. Lower still, on coilovers, and I wouldn't skip them. If you're still deciding how low to go, I wrote about that in Lowering Springs or Coilovers on a P1 Volvo?.
Don't Forget Rear Toe
Camber gets all the attention, but rear toe is the other half of how the tyre sits on the road. It has a big say in whether the car tracks straight and how the inner edges wear.
From the factory, rear toe is adjustable with an eccentric on the lower arm. After you've lowered the car, that range isn't always enough, especially if you've gone lower than a mild spring drop. That's where adjustable toe arms come in.
We do our own ALG Rear Toe Adjustment Kit for the P1, in the same orange as the camber arms, and there's a Hardrace adjustable rear toe arm as well, which uses pillow-ball joints if you want less compliance. Both are a bolt-on pair. Don't set them by measuring the old arm length and hoping.
On a modest 30mm drop, I'd get the camber arms on and let the garage see whether the factory toe adjustment still has enough range. If it doesn't, or you're going lower, fit the toe arms too. Change one and the other moves, so they should be set as a pair.
Get a Proper Four-Wheel Alignment Afterwards
This bit matters more than the brand of arm you buy. Once the new arms are on, take the car to a garage that can do a proper four-wheel alignment, not a quick front-only tracking check. Rear camber and rear toe both need setting, and the front should be set to the rear thrust line so the car doesn't crab down the road.
We sell the parts, we don't fit them or do the alignment. Get a local garage or alignment specialist to do the job.
For a road car, I wouldn't invent a custom "lowered P1" alignment sheet. Ask them to aim around the factory figures, and for rear camber to stay towards the less-negative end of that range so you're not chewing the inner edges. On a standard P1, the factory mid-spec is around -1.5 degrees of rear camber, and that's a sensible everyday target. A little toe-in at the rear is the factory approach as well. If you want a track or show setup, tell the garage that up front, and get the alignment done before you pile the miles on.
Other Bushes and Arms Worth a Look
While you're in there, it's worth looking at the rest of the geometry, especially on a high-mileage car. Lowering puts the anti-roll bar at an angle, so the Hardrace shortened front droplinks and uprated rear droplinks are worth doing at the same time. If you want a flatter rear end, the Hardrace Rear Anti-Roll Bar Kit is a two-hole adjustable bar.
Worn front bushes will undo a lot of the work you've just done at the rear. We stock the Powerflex P1 front lower wishbone rear bush, the Powerflex anti-lift and caster offset bush, Godflex P1 front suspension arm bushes, and the Hardrace P1 uprated front lower wishbones. On lower cars, the Roll Centre Adjusters and driveshaft spacers are worth a look as well.
You can browse the lot by model in the suspension collections: C30, S40, V50 and C70.
FAQ
Do I need camber arms if I've only dropped the car 30mm? I'd fit them. A 30mm drop is already enough to add rear camber, and the standard arms can't be adjusted. Wait and see if you like, but the inner edges of the rear tyres are usually what tell you that you've waited too long.
Can I just get an alignment without changing the arms? Get it measured, yes. The garage can set rear toe on the standard eccentric and tell you what the camber actually is. What they can't do, on the original arms, is change that camber figure. If it's already too negative, an alignment on its own won't fix the tyre wear.
Will camber arms fix inner tyre wear on their own? They let the garage put the camber back to a sensible number, which is usually the main cause. If toe is also out, or a bush is worn, you'll still have a problem, so get a four-wheel alignment afterwards.
What's the difference between the ÄLG arms and the Hardrace ones? Both are adjustable rear camber arms for the P1. Ours are S355 steel, powder coated orange to match our springs, with large bearings and hardened rubber bushes. The Hardrace arms are a forged design, with a rubber-bushed version or a pillowball option for track use. For a daily, I'd go rubber-bushed either way.
Do I need adjustable toe arms as well? Not always, on a mild drop, if the factory eccentric still has enough range. Once you're lower, or the garage can't get toe in, yes. Our ALG Rear Toe Adjustment Kit is the straightforward option; the Hardrace pair is there if you want pillow-ball joints.
Do you fit the arms or do the alignment? No. We sell the parts, we don't fit them. Get a local garage or an alignment specialist to install the arms and do a four-wheel alignment afterwards.
Still Not Sure?
Tell me the car, how far you've lowered it (springs or coilovers), and whether the rear tyres are already wearing. I'll point you at the right arms and skip the ones you don't need. Email sales@algperformance.co.uk.
Cheers, Sam